M.Kawabata, T.Sasaki, K.Wada, S.Kanemaru, Y.Nomura, H.Sasahara,
Welding torch with coaxial wire feed and rotating electrode for wire-arc directed energy deposition,
Additive Manufacturing, 84 (2024) 104106.
Toshiaki Otsuki, Hiroyuki Sasahara,
Block processing time-based programming for high-speed, high-precision 5-axis machining,
Precision Engineering, 88 (2024), 497-515.
I.Radchenko, W.Takahashi, H.Takahashi, T.Abe, H.Sasahara,
Introduction of internal circulation-based cooling methods and green coolants in milling via cutting tool and tooling design,
Applied Science, 14, 1379 (2024.02).
Y.Ochi, M.Usui, H.Sasahara,
Influence of Reverse Finishing on Characteristics of Drilling Surface,
International Journal of Automation Technology, 18, 3 (May 2024) 332-341.
I. Radchenko, W. Takahashi, H. Takahashi, and H. Sasahara,
Internal coolant circulation-based tool design to reduce the temperature and heat spreading when turning SUS304 Stainless Steel,
Journal of Journal of Advanced Mechanical Design, Systems and Manufacturing, 18,4 (2024) paper No.23-00383.
M.Kawabata, T.Sasaki, K.Wada, S.Kanemaru, Y.Nomura and H.Sasahara,
Effect of arc length on deposition characteristics in rotary TIG torch,
Journal of Journal of Advanced Mechanical Design, Systems and Manufacturing, 18,4 (2024) paper No.23-00552.
倉茂周治，野村衛，伊藤幸男，福原義也，笹原弘之，
円筒型ダイヤ電着金網砥石によるCFRPの大径穴加工，
砥粒加工学会誌，掲載決定.
K.Nakajima, H.Sasahara, H.Nagamatsu, T.Abe,
ERTi-2 cladding layer formation on a 5052 plate by a weaving strategy with wire and arc additive manufacturing,
The International Journal of Advanced Manufacturing Technology, 掲載決定.
#M.Makino, K.Utsumi, and H.Sasahara,
Effect of Tool Posture on Chatter Vibration in Turn-milling,
Precision Engineering, 79, (January 2023), pp. 335-348.
M.Nomura, S.Kurashige, Y.Ito, Y.Fukuhara, H.Sasahara,
Development of Electrodeposited Wire Mesh Grinding Wheel for Cutoff and Grooving Carbon Fiber Reinforced Plastic,
Materials, (2023), 16(15), 5247.
Ilia Radchenko, Wataru Takahashi, Hidebumi Takahashi, Hiroyuki Sasahara,
Effects of Internal Coolant Circulation-based Cooling Schemes on Tool Wear in Turning SUS304 Stainless Steel,
The International Journal of Advanced Manufacturing Technology, 129(Oct. 2023) pp.3141?3154 .
H.Nagamatsu, T.Abe, K.Nakajima, H.Sasahara,
Development of directed energy deposition strategy for mechanically interlocked Ti-Al component with cross-shaped internal Ti lattice,
Additive Manufacturing, Volume 78, 25 (September 2023), 103895,
T.Otsuki, K.Okita, H.Sasahara,
Evaluating surface quality by luminance and surface roughness,
Precision Engineering, 74 (March 2022) 147-162.
H.Nagamatsu, H.Sasahara,
Improvement of Cooling Effect and Dimensional Accuracy of Wire and Arc Additive Manufactured Magnesium Alloy by Active-Cooling-Based Contacting Copper Blocks,
Journal of Manufacturing and Materials Processing, 6, 2 (2022) 27.
Y.Ito, Y.Kita, Y.Fukuhara, M.Nomura, H.Sasahara,
Development of In-Process Temperature Measurement of Grinding Surface with an Infrared Thermometer,
Journal of Manufacturing and Materials Processing, 6, 2 (2022) 44.
Y.Kamada, A.Kitakaze, K.Sannomiya, T.Nakaya, H.Sasahara,
Mechanism to suppress regenerative chatter vibration due to the effect of air-cutting and multiple regeneration during low frequency vibration cutting, Precision Engineering,
Precision Engineering, 78 (November 2022) 1-18.
Junjie He, R.Yokota, Y.Imamiya, K.Noriyama, H.Sasahara,
Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition,
Materials, 15(22) (November 2022) 7985.
H.Nagamatsu, T.Abe, H.Sasahara,
Microstructure Evaluation of the Potential of Additive Manufactured Dissimilar Titanium?Aluminum alloys, Materials,
Materials, 15(24) (December 2022) 9038.
M.Makino, K.Utsumi, and H.Sasahara,
Effect of Tool Posture on Chatter Vibration in Turn-milling,
Precision Engineering, 79 (January 2023) 335-348.
T.Abe, H.Sasahara,
Simulating the build shape for a shell structure for wire and arc additive manufacturing using the bead cross-section model,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 15, 1 (January 2021) Paper No.20-00422.
Mohamed O. Helmy, Hassan El-Hofy, Hiroyuki Sasahara, M. H. El-Hofy,
Rake angle effects on ultrasonic-assisted edge trimming of multidirectional CFRP laminates, The International,
Journal of Advanced Manufacturing Technology, 115 (June 2021) 3467?3484.
Nur Syuhada Nasir, Norfariza Ab Wahab, Badri Bin Sofian, Raja Izamshah, Hiroyuki Sasahara,
Experimental Investigations Towards Hole Accuracy in Micro-drilling of Carbon Fibre Reinforced Polymer,
Material, Manufacturing Technology, 21, 3 (June 2021) 381-386.
K.Wickramasinghe, H.Sasahara, M.Usui,
Performance evaluation of a sustainable metal working fluid applied to machine Inconel 718 and AISI 304 with minimum quantity lubrication,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 15, 4 (July 2021).
K.Wickramasinghe, H.Sasahara, E.A. Rahim, G.I P Perera,
Recent advances on high performance machining of aerospace materials and composites using vegetable oil-based Metalworking Fluids,
Journal of Cleaner Production, 310, 10 (August 2021) 127459.
M. Amirul Adli, N. Ab Wahab, M. Harezul Abd Razak, M. Ridzuan Azizzi, Mohd Hadzley Abu Bakar, H. Sasahara,
Micro-Influence of Vacuum Block Positions on Machinability of Acrylic Using Hybrid Vacuum Clamping System,
International Journal of Nanoelectronics and Materials, Vol 14 (Special Issue) (August 2021) pp.145-158.
Y.Kamada, H.Sasahara,
Residual stress fluctuates periodically via the workpiece rotation phase during low frequency vibration cutting,
Precision Engineering, 72, (November 2021) 583-594.
R.Miyake, H.Sasahara, A.Suzuki, S.Ouchi,
Wire Arc Additive and High-Temperature Subtractive Manufacturing of Ti-6Al-4V,
Applied Science, 11, 20 (2021) 9521.
K.C Wickramasinghe, H.Sasahara, E.A.Rahim, G.I.P.Perera,
Green Metalworking Fluids for sustainable machining applications: A review,
Journal of Cleaner Production, 257 (June 2020).
H.Nagamatsu, H.Sasahara, Y.Mitsutake, T.Hamamoto,
Development a cooperative system for wire and arc additive manufacturing and machining,
Additive manufacturing, 31 (January 2020).
K.Utsumi, S.Shichiri, H.Sasahara,
Determining the effect of tool posture on cutting force in a turn milling process using an analytical prediction model,
International Journal of Machine Tools and Manufacture, Vol. 150 (March 2020) 103511.
T.Abe, J.Kaneko, H.Sasahara,
Thermal sensing and heat input control for thin-walled structure building based on numerical simulation for wire and arc additive manufacturing,
Additive Manufacturing, Volume 35 (October 2020) 101357.
三宅章仁，北風絢子，櫻井聖子，村松正博，野口賢次，三宮一彦，中谷尊一，鎌田陽，笹原弘之,
低周波振動切削が創生する加工面形状に関する研究,
日本機械学会誌論文集，Vol.86, No.892 (2020) p.20-00323.
T.Otsuki, H.Sasahara, R.Sato,
Method to evaluate speed and accuracy performance of CNC machine tools by speed-error 2-D representation,
Journal of Advanced Mechanical Design, Systems, and Manufacturing (2019) Vol.13, No.1.
A.S.A.Sani, E.A.Rahim, S.Sharif, H.Sasahara,
The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045,
Tribology International, 129 (January 2019), pp.347-362.
T.Otsuki, H.Sasahara, R.Sato,
Method for Generating CNC Programs Based on Block-Processing Time to Improve Speed and Accuracy of Machining Curved Shapes,
Precision Engineering, 55(2019) pp.33-41.
T.Abe, D.Mori, K.Sonoya, N.Masanobu, H.Sasahara,
Control of the Chemical Composition Distribution in Deposited Metal by Wire and Arc-based Additive manufacturing,
Precision Engineering, 55(2019) pp.231-239.
H.Takagi, H.Sasahara, T.Abe, H.Sannomiya, S.Nishiyama, S.Ohta, K.Nakamura,
Material-property evaluation of magnesium alloys fabricated using wire-and-arc-based additive manufacturing,
Additive Manufacturing, available on line.
A.S.A.Sani, E.A.Rahim, S.Sharif, H.Sasahara,
Machining performance of vegetable oil with phosphonium- and ammonium-based ionic liquids via MQL technique,
Cleaner Production, 209 (2019) 947-964.
K.Suzuki, R.Koyasu, Y.Takeda, H.Sasahara,
Application of a Novel Woven Metal Wire Tool with Electrodeposited Diamond Grains for Carbon Fiber Reinforced Plastics Core Drilling,
Precision Engineering, in press.
K.C Wickramasinghe, G.I.P. Perera, Himan KG Punchihewa and H.Sasahara,
Surface Quality Evaluation of 0.2% C and AISI 304 Steels in Turning with Sustainable lubricating Condition,
Journal of Mechanical Science and Technology, 33, 12 (2019) pp.5753~5759.
S.Toyokawa, N.Nakatsuka, A.Kusakabe, H.Sasahara,
Surface Characteristic on Curved Grinding of Titanium Alloy with Coolant Supplying from Inner Side of Grinding Wheel,
Key Engineering Materials, 825 (October 2019), pp 84-91.
N.Nakatsuka, S.Toyokawa, A.Kusakabe, S.Nakatsukasa, H.Sasahara,
Effect of the Type of Grinding Wheel on the Surface Characteristic of Titanium Alloy with Internal Coolant Supply,
Key Engineering Materials, 825 (October 2019), pp 92-98.
T.Tsurumaki, H.Chibahara, S.Tsukamoto, H.Sasahara,
Precise additive fabrication of wall structure on thin plate end with interlayer temperature monitoring,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 13, 2 (April 2019) Paper No.19-00070
松原光作，土村潤，豊川澄斗，笹原弘之，
小径砥石によるコーナ部内面研削における砥石内液供給の冷却効果に関する研究，
砥粒加工学会誌，63, 10 (2019) p. 528-533.
Y.Takada, H.Sasahara,
Effect of Tip Shape of Frictional Stir Burnishing Tool on Processed Layer’s Hardness,
Residual Stress and Surface Roughness, Coatings, 8, 1 (2018) 32.
H.Sasahara, Y.Sukegawa, Y.Yamada,
CFRP machining capability by a circular saw,
Precision Engineering, 52 (2018) 291-299.
福原義也，鈴木修平，笹原弘之，
砥石表面の特徴的な温度変動に基づく研削加工時の異常発生のインプロセス判別，
砥粒加工学会誌，62, 4 (2018) pp.204-210.
A.Miyake, H.Sasahara, A.Kitakaze, S.Katoh, M.Muramatsu, K.Noguchi, K.Sannomiya, T.Nakaya,
Chip Control in Turning with Synchronization of Spindle Rotation and Feed Motion Vibration,
Precision Engineering, 53 (2018) pp.38-45.
H. Sasahara, K. Satake, W. Takahashi, M. Goto and H. Yamamoto,
The Effect of Oil Mist Supply on Cutting Point Temperature and Tool Wear on Driven Rotary Cutting,
recision Engineering, 48 (2017) 158-163.
N. Talib, H. Sasahara, E. A. Rahim,
Evaluation of modified jatropha-based oil with hexagonal boron nitride particle as a biolubricant in orthogonal cutting process,
The International Journal of Advanced Manufacturing Technology, 92 (2017) pp. 371-391
E. A. Rahim, H. Sasahara,
Performance of palm oil as a biobased machining lubricant when drilling inconel 718,
MATEC Web of Conferences, vol. 101 (2017)
T. Otsuki, H. Sasahara, R. Sato,
A method for the evaluation and magnified representation of two-dimensional contouring error,
Precision Engineering, 50 (2017) pp. 433-439.
K. Okamura, H. Sasahara,
Prediction of drilling temperature during low-frequency vibration drilling of titanium alloy,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 11, 3 (2017) Paper No.16-00431,
E. A. Rahim, H. Sasahara,
Three Dimensional Finite Element Modeling when Drilling of Ti-6Al-4V,
International Journal of Robotics and Mechatronics, Vol. 4, No. 1 (2017) pp.33-38
Y. Fukuhara, S. Suzuki, H.Sasahara,
Real-time Grinding State Discrimination Strategy by Use of Monitor-embedded Grinding Wheels,
Precision Engineering, Vol.51 (2018) pp.128-136.
Kai Xu and H. Sasahara,
Generation of Uniformly Aligned Dimples on a Curved Surface Using a Curved-Surface Patch-Division Milling Technique,
Int. J. of Automation Technology, 10, 1(2016-01) pp.23-29.
T. Abe and H. Sasahara,
Dissimilar metal deposition with stainless steel and nickel based alloy by wire and arc based additive manufacturing,
Precision Engineering, 45 (2016) pp.387-395. doi:10.1016/j.precisioneng.2016.03.016
岡村清志，笹原弘之,
低周波振動穴あけの摩耗低減機構の解明，
砥粒加工学会誌，60, 6 (2016-06) pp.320-325.
T. Nakamura, H. Sasahara, S. Kusunose and I. Nishizaki,
Identification of Aluminum Alloy Flow Stress to Determine FEM Analysis Constitutive Equation for Machining Material,
Materials Science Forum, Vol. 874, pp.457-462, doi:10.4028/www.scientific.net/MSF.874.457
H. Sasahara, K. Satake, W. Takahashi, M. Goto and H. Yamamoto,
The Effect of Oil Mist Supply on Cutting Point Temperature and Tool Wear on Driven Rotary Cutting,
Precision Engineering, 48 (2017) pp.158-163. doi:10.1016/j.precisioneng.2016.11.016
Takeyuki Abe and Hiroyuki Sasahara,
Development of the Shell Structures Fabrication CAM System for Direct Metal Lamination Using Arc Discharge -Lamination Height Error Compensation by Torch Feed Speed Control-,
International Journal of Precision Engineering and Manufacturing, 16, 1 (2015-01) pp.171-176．
内海幸治，河野一平，小野塚英明，加藤吐夢，笹原弘之，
薄板加工におけるびびり振動抑制用動吸振器の設計方法に関する研究，
精密工学会誌，81，2(2015) pp.187-192．
Norfariza Wahab, Hiroyuki Sasahara,
Identification of Friction Characteristics and Flow Stress of 0.45% Carbon Steel during Cutting Process,
Advanced Materials Research, 1101 (2015-04) pp.402-405. 10.4028/www.scientific.net/AMR.1101.402
Norfariza Wahab, Hiroyuki Sasahara, Shinnosuke Baba, Yuta Hiratsuka, Takashi Nakamura,
Development of High-speed Shearing Method to Obtain the Flow Stress under High Strain Rate,
International Journal of Modeling and Optimization, 5, 2, April (2015-04), pp.140-144. DOI 10.7763/IJMO.2015.V5.450.
Masato Goto, Wataru Takahashi, Wataru Sasaki, Takeshi Toujyo, Yuji Takagi Hiromasa Yamamoto and Hiroyuki Sasahara,
Effect of cutting conditions on tool wear in driven rotary cutting of maraging steel,
Key Engineering Materials Vols 656-657 (2015-07) pp.208-213. doi:10.4028/www.scientific.net/KEM.656-657.208
Hisataka Takagi, Takeyuki Abe, Peng Cui and Hiroyuki Sasahara,
Mechanical Properties Evaluation of Metal Components Repaired by Direct Metal Lamination,
Key Engineering Materials Vols 656-657 (2015) pp.440-445. doi:10.4028/www.scientific.net/KEM.656-657.44
K. Nomura, N. Takeuchi, A. Kusakabe, M. Chino and H. Sasahara,
Improvement of surface roughness with micro-axial vibration of spindle by pressure pulsation of
grinding fluid supplied through inside of wheel, Advances Materials Research, 806 (2015) pp.673-677.
Y. Fukuhara, S. Suzuki and H. Sasahara,
Development of in-process monitoring system for grinding wheel surface temperature and grinding state,
Advances Materials Research, 806 (2015) pp.624-629.
高田正義，笹原弘之，
二重らせん経路での摩擦攪拌形バニシングによる高硬度・圧縮残留応力を両立する表面強化層の創成，
日本機械学会論文集，81，830 (2015) No.15-00350 [DOI:10.1299/transjsme.15-00350].(早期公開9月25日)
Norfariza Wahab, Yumi Inatsugu, Satoshi Kubota, Soo Young Kim, Hiroyuki Sasahara,
An Integral Method to Determine Workpiece Flow Stress and Friction Characteristics in Metal Cutting,
International Journal of Automation Technology, 9, 6 (2015-11) pp.775-781.
Yohei Yamada and Hiroyuki Sasahara,
Free-form curves cutting using flexible circular saw, Precision
Engineering, 38, 3 (2014) pp.611-616. DOI: 10.1016/j.precisioneng.2014.02.011
Hiroyuki Sasahara, Tomoko Kikuma,
Rei Koyasu, Yasuhiro Yao, Surface grinding of carbon ?ber reinforced plastic
(CFRP) with an internal coolant supplied through grinding wheel, Precision Engineering, 38, 4 (2014) pp.775-782.
DOI: 10.1016/j.precisioneng.2014.04.005
Wataru Takahashi, Hiroyuki Sasahara , Hiromasa Yamamoto, Yuji
Takagi, FEM simulation on the effect of cutting parameters in the driven rotary
cutting, Key Engineering Materials, 625 (2015) pp.564-569. doi:10.4028/www.scientific.net/KEM.625.564
Norfariza Wahab, Yumi Inatsugu, Satoshi Kubota, Soo Young Kim, Hiroyuki Sasahara,
Identification of Flow Stress Applicable for FEM Simulation of Orthogonal Cutting Process,
Key Engineering Materials, 625 (2014-08) pp.378-383. doi:10.4028/www.scientific.net/KEM.625.378
Nagatoshi Nakatsuka, Yudai Hirai, Atushi Kusakabe, Yasuhiro Yao and Hiroyuki Sasahara,
Effect of coolant supplied through grinding wheel on residual stress of grinding surface,
Advanced Materials Research, 1017 (2014-09) pp.33-37. doi:10.4028/www.scientific.net/AMR. 1017.33
Kosaku Matsubara, Jun Tsuchimura, Shota Kawazoe and Hiroyuki Sasahara,
Form accuracy of internal grinding of small and deep holes with coolant supplied from inner side of grinding wheel,
Advanced Materials Research, 1017 (2014-09) pp.50-54. doi:10.4028/www.scientific.net/AMR.1017.50
八尾泰弘，李志，中江慶吾，笹原弘之，
超砥粒電着砥石における砥石内研削液供給機構の効果，
砥粒加工学会誌，57,4 (2013) pp.229-234.
田中敬三，阿部壮志，吉丸玲欧，笹原弘之，
アーク放電を用いた溶融金属積層による造形物の強度，
日本機械学会誌論文集（C編），79,800 (2013) pp.1168-1178.
Takeshi Yashiro, Takayuki Ogawa and Hiroyuki Sasahara,
Temperature measurement of cutting tool and machined surface layer in milling of CFRP,
International Journal of Machine Tools and Manufacture, 70 ,7 (2013) pp.63-69. http://dx.doi.org/10.1016/j.ijmachtools.2013.03.009
Kai Xu and Hiroyuki Sasahara,
Generation of Regularly Aligned Dimples on Triangular Pyramidal Patches Using
Patch Division Milling, Int. J. of Automation Technology,7, 6 (2013) pp.751-759.
上岡利人，阿部壮志，石川修平，笹原弘之，
アーク放電を用いた溶融金属積層時の溶融池の冷却方法による積層特性への影響，
日本機械学会誌論文集（C編），78, 785(2012) 282-291.
Kan Ding, Hiroyuki Sasahara,
Study on the Machining of Iron-Based Thermal Spray Coating for Sleeveless Engine Cylinder,
Advanced Materials Research, Vols.472-475 (2012) pp. 991-996.
笹原弘之，木内智，矢田智彦，富永啓介，
炭素鋼S45Cへの摩擦攪拌形バニシング加工による硬化組織の創成，
日本機械学会誌論文集（C編），78, 787 (2012) pp. 996-1003.
笹原弘之，田中敬三，吉丸玲欧，
溶融金属積層における造形条件と強度・金属組織に関する研究，
精密工学会誌， 78, 5 (2012) 415-419.
田中敬三，笹原弘之，
プレス金型におけるトリム刃型製造方法の研究−(NC マシンによる溶融金属積層と積層金属の開発，
日本機械学会誌論文集（C編），78, 790 (2012) 2340-2349.
八尾泰弘，李志，中江慶吾，笹原弘之，
砥石内研削液供給方式による研削液の少量化とその効果，
精密工学会誌，78, 8 (2012) pp.710-715．
Takeyuki Abe and Hiroyuki Sasahara,
Residual Stress and Deformation after Finishing of a Shell Structure Fabricated by Direct Metal Lamination Using Arc Discharge,
Int. J. of Automation Technology，6, 5 (2012) pp. 611-617．
Yohei Yamada, Nobuyuki Osumi, Akio Takasugi, Hiroyuki Sasahara,
Curved Line Cutting Using Flexible Circular Saw,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 6, 6 (2012) pp.971-978.
E. A. Rahim, Z. Mohid, K. C. Mat, M. F. M. Jamil, R. Koyasu, and H. Sasahara,
Hole Making Process of Carbon Fiber Reinforced Polymer (CFRP) Using End Mill Cutting Tool,
Advanced Materials Research,576 (2012) pp. 64-67.
E. A. Rahim, Z. Mohid, M. F. M. Jamil, K. C. Mat, R. Koyasu and H. Sasahara,
Experimental Study of Helical Milling on CFRP (Carbon Fibre Reinforced Polymer) for the Hole Making Process,
Advanced Materials Research,576 (2012) pp. 68-71.
Kai Xu and Hiroyuki Sasahara,
Generation of Regularly Aligned Curved Surface Patches on Free-form Surface for Patch Division Milling,
Key Engineering Materials, Vols. 523-524 (2012) pp.54-57.
Zhi Li, Yasuhiro Yao, Keigo Nakae and Hiroyuki Sasahara,
Temperature Measurement of Surface Grinding Using a Fluid Supplying System from Inside of Grinding Wheel,
Key Engineering Materials, Vols. 523-524 (2012) pp.125-130.
Erween Abd. Rahim, Hiroyuki Sasahara,
Investigation of tool wear and surface integrity on MQL machining of Ti-6AL-4V using biodegradable oil,
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture,
September 2011; vol. 225, 9: pp. 1505-1511.
八尾泰弘，不破洋平，笹原弘之，
砥石内研削液供給機構による難削材形状研削加工に関する研究，
日本機械学会誌論文集（C編），77, 781(2011) 3522-3531．
山本博雅，佐竹健太郎，笹原弘之，成田徹，堤正臣，村木俊之，
駆動型ロータリ切削による難削材の高能率加工におけるMQLの効果−工具温度と切りくず凝着−，
精密工学会誌，77, 3, (2011) pp.316-321.
Erween Abd. Rahim, Hiroyuki Sasahara,
An Analysis of Surface Integrity when Drilling Inconel 718 using Palm Oil and Synthetic Ester under MQL Condition.
Machining Science and Technology, 15, 1, (2011) pp.76 ? 90.
Erween Abd. Rahim, Hiroyuki Sasahara,
A Study of the Effect of Palm oil as MQL Lubricant on High Speed Drilling of Titanium Alloys,
Tribology International, accepted, published online.
Erween Abd. Rahim, Hiroyuki Sasahara,
A Study of the Effect of Palm oil as MQL Lubricant on High Speed Drilling of Titanium Alloys,
Tribology International, accepted, published online.
Toshihito Kamioka, Syuhei Ishikawa and Hiroyuki Sasahara,
Fabrication of Elbow Pipe by Direct Metal Lamination Using Arc Discharge while Maintaining the Molten Pool in a Horizontal Position,
Int. J. of Automation Technology, 4, 5 (2010) pp.422-431.
Satoshi Kiuchi and Hiroyuki Sasahara,
Temperature History and Metallographic Structure of 0.45%C Steel Processed by Frictional Stir Burnishing,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 4, 5 (2010) pp.838-.848.
Kan Ding, Hiroyuki Sasahara, Syuji Adachi and Kimio Nishimura,
Investigation on the Cutting Process of Plasma Sprayed Iron Base Alloys,
Key Engineering Materials, 447-448 (2010) pp. 821-825.
Erween Abd. Rahim, Hiroyuki Sasahara,
Effect of Machining Parameters and MQL Liquids on Surface Integrity of High Speed Drilling Ti-6Al-4V,
Key Engineering Materials, 447-448 (2010) pp. 816-820.
Erween Abd. Rahim, Hiroyuki Sasahara,
Surface Integrity in MQL Drilling Nickel-Based Superalloy,
Key Engineering Materials, 447-448 (2010) pp. 811-815.
Hiromasa Yamamoto, Kentaro Satake, Hiroyuki Sasahara, Toru Narita, Masaomi Tsutsumi, Toshiyuki Muraki,
Thermal Behavior and Tool Failures on Rotary Cutting of Difficult-to-cut Materials Utilizing Multi Tasking Lathe,
Key Engineering Materials, 447-448 (2010) pp. 806-810.
Erween Abd. Rahim, Hiroyuki Sasahara,
Surface Integrity when Drilling Nickel-Based Superalloy under MQL Supply,
Key Engineering Materials, 443 (2010) pp. 365-370.
Erween Abd. Rahim, Hiroyuki Sasahara,
Effect of MQL Liquids on Surface Integrity when High Speed Drilling Titanium Alloy,
Key Engineering Materials, 443 (2010) pp. 359-364.
福田理明，笹原弘之，松田礼，堤正臣：
パッチ分割切削法による任意三角形パッチ内への規則的表面模様形成，
精密工学会誌, 76, 1 (2010) pp.111-115.
伊藤尚功，K.M.Muditha Dassanayake，五十嵐大輔，笹原弘之：
平面カムのエンドミル切削における加工精度の予測と制御，
日本機械学会誌論文集（C編），75, 757 (2009) pp.2475-2482.
笹原弘之，松丸哲史，上岡利人，田中敬三，吉丸玲欧：
溶融金属積層による傾斜壁の造形―積層形状に及ぼす諸因子とその影響―，
日本機械学会誌論文集（C編），75, 757 (2009) pp.2435-2439.
崔剿ﾁ，下村充，笹原弘之：
シーケンシャル切削における熱的状態と残留応力状態の解析的予測，
日本機械学会誌論文集（C編），75, 757 (2009) pp.2404-2409.
Toshiyuki Obikawa, Yoshifumi Takemura, Yasuhiro Akiyama, Jun Shinozuka, Hiroyuki Sasahara,
Microscopic Phase-Dependent Residual Stresses in the Machined Surface Layer of Two-Phase Alloy:
FE Modeling and Results,
Journal of Materials Processing Technology,
209, 9 (2009) pp. 4496-4501.
Kei Harada, Hiroyuki Sasahara,
Effect of Dynamic Response and Displacement/Stress Amplitude
on Ultrasonic Vibration Cutting,
Journal of Materials Processing Technology, 209, 9 (2009)
pp.4490-4495.
Erween Abd. Rahim, Hiroyuki Sasahara,
Application of Minimum Quantity Lubrication when
Drilling Nickel-Based Superalloy at High Cutting Speed, Key Engineering Materials, 407-408
(2009) pp.612-615.
Hiroyuki Sasahara, Yoshihisa Naito,
Prediction and Avoidance of Chatter in Milling of
Thin-walled Structure,
Key Engineering Materials, 407-408 (2009) pp.404-407.
Hiroyuki Sasahara, Makoto Kawasaki, Masaomi Tsutsumi,
Helical Feed Milling with MQL for Boring of Aluminum Alloy,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2, 6 (2008) pp.1030-1040.
Ryuji Iwashita, Hiroyuki Sasahara,
Study on Simulation of Micro Cutting Process of Alternatively Arranged Resin and Metal,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2, 4 (2008) pp.711-718.
Hiroshi Nakajima, Atsushi Kato, Hiroyuki Sasahara, Hiromasa Yamamoto, Toshiyuki Muraki, Masaomi Tsutsumi,
Effect of Rotary Cutting Tool Posture on Multi Tasking Lathe,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2, 4 (2008) pp.532-539.
Hiroshi Matsuda, Hiroyuki Sasahara, Masaaki Fukuda and Masaomi Tsutsumi,
Tool Path Generation for the Formation of a Geometric Surface Pattern on a Curved Surface by Patch Division Milling,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2, 4 (2008) pp.504-512.
YuLong Tang, Kan Ding, Hiroyuki Sasahara, Kimio Nishimura, Takafumi Watanabe,
Clarification of the Amount of Machining Error Resulting from the Cutting Force and the Thermal Expansion during Cylinder Liner Boring Process,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2, 3 (2008) pp.332-342.
YuLong Tang and Hiroyuki Sasahara,
Analytical Prediction of Temperature Distribution in Cylinder Liner during Various Boring Operations,
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2, 3 (2008) pp.278-289.
Hiroyuki Sasahara, Atsushi Kato, Hiroshi Nakajima, Hiromasa Yamamoto, Toshiyuki Muraki, Masaomi Tsutsumi,
High-speed Rotary Cutting of Difficult-to-Cut Materials on Multi-Tasking Lathe,
International Journal of Machine Tools and Manufacture, 48, 7-8 (2008) pp.841-850.
Hiroshi Matsuda, Hiroyuki Sasahara, Masaomi Tsutsumi,
Generation of a Regularly Aligned Surface Pattern and Control of Cutter marks Array by Patch Division Milling,
International Journal of Machine Tools and Manufacture, 48, 1 (2008) pp.84-94.
Tang Yu Long and Hiroyuki Sasahara,
Investigation of thermal behavior on cylinder liner during its boring process,
International Journal of Machine Tools and Manufacture, 47, 14 (2007) pp.2162-2171.
笹原弘之，長尾昇平，茅野雅久：
姿勢制御電極による電解曲がり穴加工，
日本機械学会誌論文集（C編），73, 733 (2007) pp.2619-2624.
松田礼，笹原弘之，堤正臣：
仕上げ面凹凸模様の配列に及ぼす直進軸の加減速と主軸速度の偏差の影響，
精密工学会誌，73, 3 (2007) pp.355-359.
松田礼，笹原弘之，瀧澤誠，堤正臣：
パッチ分割切削法による平面への規則的表面模様形成，
精密工学会誌, 72, 9 (2006) pp.1123-1127.
笹原弘之，浅野穣：
高速回転するエンドミル周りの熱伝達に関する研究，
精密工学会誌, 72, 9 (2006) pp.1103-1107.
笹原弘之，石坂新吾：
二相合金切削における加工変質層の繰り返し切削の影響，
日本機械学会誌論文集（C編），72, 720 (2006) pp.2634-2640.
Yuji Furukawa, Hiroyuki Sasahara, Akira Kakuta, Kenichiro Chuma,
Principal Factors Affecting the Sub-Micrometer Grooving Mechanism of SiC Thin Layers by a 355 nm UV Laser,
Annals CIRP, 55, 1 (2006) pp.573-576.
笹原弘之，原昌範，田中信成，浜野瑞樹：
ニアドライ加工環境中でのミスト・油煙の発生と捕獲，
精密工学会誌，72, 8 (2006) pp.983-987.
瀬川俊明，笹原弘之，石川達郎，村瀬寛恭，堤正臣：
切削−バニシング複合加工工具の開発とその基本特性 −エンドミルタイプ複合加工工具の提案と加工表面への圧縮残留応力生成−，
精密工学会誌，72, 7 (2006), pp.909-913.
笹原弘之，内藤祥久，堤正臣：
CAD/CAEと打撃音を利用したエンドミル加工時のびびり振動の予測と回避，
精密工学会誌，72, 4 (2006), pp.534-538.
Kiyoshi Okamura, Hiroyuki. Sasahara, Toshiaki Segawa, Masaomi Tsutsumi,
Low-frequency Vibration Drilling of Titanium Alloy,
JSME International Journal, Series C, 49, 1(2006) pp.76-82.
Hiroyuki Sasahara, Masahisa Chino, Masaomi Tsutsumi,
Development of a Layered Manufacturing System Using Sheet Metal-Polymer Lamination for Mechanical Parts,
International Journal of Advanced Manufacturing Technology, 27, 3-4 (2005) pp.268-273.
原田圭，笹原弘之：
超音波振動切削における切削機構に関する研究(第3報)−加工雰囲気による潤滑状態の変化−，
精密工学会誌，71, 8 (2005) pp.1005-1009.
瀬川俊明，笹原弘之，鍵谷夕，新槙壮一，堤正臣：
アルミニウム合金のドライ穴加工における切りくず排出過程の可視化 -切りくず排出過程に及ぼすねじれ角の影響-，
精密工学会誌，71, 5 (2005) pp.623-627.
瀬川俊明，笹原弘之，石川達郎，村瀬寛恭，堤正臣：
圧縮残留応力生成工具による加工表面の残留応力制御，
精密工学会誌，71, 4 (2005) pp.496-500.
茅野雅久，笹原弘之，土居敦，滝沢誠，堤正臣：
金属−高分子積層による造形装置の開発とマシニングセンタへの搭載，
日本機械学会誌論文集（C編），71，702 (2005) pp.713-718.
Hiroyuki Sasahara,
The Effect on Fatigue Life of Residual Stress and Surface Hardness resulting from Different Cutting Conditions of 0.45%C Steel,
International Journal of Machine Tools and Manufacture, 45, 2 (2005) pp. 131-136.
本田考耶，笹原弘之：
有限要素法による切削シミュレータの開発 −GUIの開発と工具形状の影響の検討−，
精密工学会誌，71, 1 (2005) pp.115-119.
Toshiaki Segawa, Hiroyuki Sasahara, Masaomi Tsutsumi,
Development of a New Tool to Generate Compressive Residual Stress within a Machined Surface,
International Journal of Machine Tools and Manufacture, 44, 11 (2004) pp.1215-1221.
笹原弘之，原田圭：
超音波振動切削における切削機構に関する研究(第2報)−動的応答および変位振幅・応力振幅の影響−，
精密工学会誌，70, 9 (2004) pp.1191-1195.
笹原弘之，金桂紅，神雅彦，村川正夫：
振動切削過程における振動と加工雰囲気の影響−50Hz振動切削の場合−,
日本機械学会誌論文集（C編），70, 694 (2004) pp.1843-1848.
笹原弘之，高橋琢磨，林祐一郎：
疲労寿命に及ぼす旋削仕上げによる残留応力と硬さの影響,
精密工学会誌，70, 6 (2004) pp.872-874.
瀬川俊明，笹原弘之，石川達郎，堤正臣：
圧縮残留応力生成工具の開発とその基本特性,
精密工学会誌，70, 6 (2004) pp.853-857.
Hiroyuki Sasahara, Toshiyuki Obikawa, Takahiro Shirakashi,
Prediction Model of Surface Residual Stress within a Machined Surface by Combining Two Orthogonal Plane Models,
International Journal of Machine Tools and Manufacture, 44, 7-8 (2004) pp. 815-822.
Hiroyuki Sasahara, Masaomi Tsutsumi,
Strategic Optimization of Cutting Conditions by Model-Based Analysis with the Aid of Database Utilization,
Trans. NAMRI/SME, Vol.32, (2004) pp. 581-588.
笹原弘之，原田圭：
超音波振動切削における切削機構に関する研究(第1報)−相対切削速度の変動と切りくず生成過程のシミュレーション解析−,
精密工学会誌，70, 4 (2004) pp.578-582.
笹原弘之，伊藤功次，堤正臣：
解析的手法とデータベースの併用による切削条件選定システム，
精密工学会誌，69, 12 (2003) pp.1749-1753.
笹原弘之，川崎誠，堤正臣：
MQLを適用したヘリカル送りミリングによるアルミニウム合金の穴加工,
日本機械学会誌論文集(C編)，69,684 (2003) pp.2156-2161.
笹原弘之：
動的切削過程の有限要素法解析，
精密工学会誌，69,8 (2003) pp.1124- 1128.
笹原弘之，田渕比奈子，神雅彦，村川正夫：
シェービング加工における切り口面生成過程のFEM解析,
日本機械学会誌論文集(C編)，67,654 (2001) pp.541-546.
笹原弘之，水谷文則，堤正臣：
オイルミスト供給による高速エンドミル加工時の工具摩耗への影響,
精密工学会誌，66,1 (2000) pp.80-84.
笹原弘之，帯川利之：
二相合金切削の有限要素法シミュレーション，
精密工学会誌，64, 7 (1998) pp.1083-1087.
Toshiyuki Obikawa, Hiroyuki Sasahara, Takahiro Shirakashi, Eiji Usui,
Application of Computational Machining Method to Discontinuous Chip Formation,
Trans. ASME. J. Manuf. Sci. Eng., 119 (1997) pp.667-674.
Hiroyuki Sasahara, Toshiyuki Obikawa, Takahiro Shirakashi,
Finite Element Modeling of Residual Stress Control on Machined Surface,
Trans. NAMRI/SME, Vol. XXV, (1997), pp.213-218.
Hiroyuki Sasahara, Toshiyuki Obikawa, Takahiro Shirakashi,
FEM Analysis of Cutting Sequence Effect on Mechanical Characteristics in Machined Layer,
J. Materials Processing Tech., 62, (1996) pp.448-453.
笹原弘之，帯川利之，白樫高洋：
切削工程による加工変質層の推移と制御，
精密工学会誌，61, 10 (1995) pp.1453-1457.
笹原弘之，帯川利之，白樫高洋：
切削加工変質層生成過程のシミュレーション解析（第３報），
精密工学会誌，60, 12 (1994) pp.1801-1805.
Takahiro Shirakashi, Hiroyuki Sasahara, Toshiyuki Obikawa and Takeshi Wada,
The Analytical Prediction of Residual Stress within Machined Sublayer and Its Effect on Accuracy,
Int.J.JSPE，28, 3 (1994) pp.200-205.
Hiroyuki Sasahara, Toshiyuki Obikawa, Takahiro Shirakashi,
The Prediction of Effects of Cutting Condition on Mechanical Characteristics in Machined Layer，
Advancement of Intelligent Production, Edit. E.Usui, Elsevier, (1994) pp.473-478.
Hiroyuki SASAHARA, Toshiyuki Obikawa, Takahiro Shirakashi,
FEM Analysis on Three Dimensional Cutting -Analysis on Large Deformation Problem of Tool Entry-,
Int. J. JSPE，28, 2 (1994) pp.123-128.
笹原弘之，帯川利之，白樫高洋，臼井英治：
自励びびり振動における動的切削過程の非線形効果（第４報），
精密工学会誌，60, 4 (1994) pp.565-569.
白樫高洋，帯川利之，笹原弘之，和田武司：
切削加工変質層生成過程のシミュレーション解析（第２報），
精密工学会誌，59, 12 (1993) pp.2003-2008.
白樫高洋，帯川利之，笹原弘之，和田武司：
切削加工変質層生成過程のシミュレーション解析（第１報），
精密工学会誌，59, 10 (1993) pp.1695-1700.
笹原弘之，帯川利之，白樫高洋：
三次元切削の有限要素法シミュレーション，
精密工学会誌，59，8 (1993) pp.1275-1280.
帯川利之，笹原弘之，白樫高洋，臼井英治：
自励びびり振動における動的切削過程の非線形効果（第３報），
精密工学会誌，59，7 (1993) pp.1151-1156.
帯川利之，田口克之，笹原弘之，白樫高洋，臼井英治：
せん断型切りくず生成の有限要素法シミュレーション，
精密工学会誌，59，5 (1993) pp.821-826.
帯川利之，笹原弘之，臼井英治：
チップブレーカ作用の有限要素法解析，
精密工学会誌，58，12 (1992 ) pp.2051-2056.
臼井英治，帯川利之，笹原弘之，白樫高洋：
自励びびり振動における動的切削過程の非線形効果（第２報），
精密工学会誌，56，4 (1990) pp.661-666.
臼井英治，井原透，笹原弘之，白樫高洋：
自励びびり振動における動的切削過程の非線形効果（第１報）,
精密工学会誌，55，11 (1989) pp.2017-2023.